Cross Stitch Soldiers Cards, Frames and Tags – Free sewing patterns

Essentials

Fabric: Aida, 11 count, 17.5cm x 22.5cm, for picture; Aida, 14 count, 10cm x 15cm, for single motif card; Hardanger, 22 count, 10cm x 15cm, for triple motif card; 8cm x 12cm, for tag; cotton, 8cm x 12cm, for tagThread: embroidery, six stranded, one skein each: navy blue; red; white; yellow-gold; beige; skin tone; black; brown; sewing, strongEmbroidery hoopNeedles, tapestryFrame, 12cm x 16.5cm apertureWadding, 7.5cm x 8cmCard: white; blueBias binding, satin, blue, 50cmCraft knifeRuler, steelGlue, fabric

Dimensions List

Tag 7.5cm x 12cmOne soldier card 10cm x 15cmThree soldiers 11.5cm x 12cmPicture 16.5cm x 21.5cm

Stitch a soldier picture

Locate and download the charts and cut 11 count Aida fabric to 17.5cm x 22.5cm, or larger if you are using an embroidery hoop. Mark the centre of the fabric.

Thread a blunt-ended tapestry needle with three strands of yellow-gold embroidery thread and follow the soldier and castle chart to stitch the belt buckle, then the buttons. Change to red thread and stitch the jacket, then continue following the chart until the whole design has been worked.

For a neat appearance, make sure that the top and bottom threads on each cross stitch lie in the same direction. Remove the work from the hoop, then press lightly on the reverse, under a damp cloth, to remove any creases.

To frame the picture, cut a piece of card to fit inside the chosen frame, in this case 13cm x 18cm, and place it on the centre back of the embroidery. Trim the fabric, if necessary, to give a border of 3cm all around, then fold it over the edges of the card.

Either glue it together or lace the edges of the fabric together with thread. Remove the glass, then position the embroidery inside and replace the backing board.

Make a single soldier greeting card

Follow the first stage as per the soldier and castle picture, but use a 14 count Aida fabric measuring 10cm x 15cm, or larger if using a hoop. Embroider as before, using two strands of thread rather than three, to cross stitch the middle soldier from the group.

Continue using the colours indicated in the key until the whole design has been worked. Remove the fabric from the hoop or frame and press on the reverse under a damp cloth to remove creases. Cut blue card measuring 15cm x 20cm and fold in half, then mark out a 4cm x 8cm opening in the front, and cut out neatly using a craft knife.

Trim the fabric to 6cm x 10cm, then place behind the opening, making sure the embroidery is centred. Glue the edges of the fabric on the inside of the card. Cut a piece of card 9.5cm x 14.5cm and stick this on the inside front, to cover the fabric and produce a neat finish.

Create a three soldier card

Follow instructions for the single soldier card, but instead use a 22 count Hardanger fabric measuring 10cm x 15cm and stitch all three soldiers, using two strands of thread. Marking out a central point will help to centre the design when following the chart.

Cut a 12cm x 23cm piece of white card and fold in half, then with the fold at the top, mark out an opening in the front 7.5cm x 8cm, and cut out using a craft knife. Trim fabric to 10cm x 10.5cm, then place behind the aperture, ensuring the embroidery is centred. Glue the edges of the fabric on the inside of the card.

To cover the fabric on the inside front of the card, cut a 9.5cm x 14.5cm piece of card and glue. For a slightly padded effect, place a piece of wadding smaller than the aperture at the back of the cross stitch before glueing down the backing card. For extra detail add a blue border to the front.

Sew a guardsman gift tag

Mark the centre of an 8cm x 12cm piece of 22 count Hardanger fabric, thread a blunt-ended tapestry needle with two strands of white thread and referring to the chart with a soldier in the sentry box, begin to cross stitch the belt. Continue following the chart, using the colours indicated in the key, until the whole design is complete.

Remove the fabric from the hoop, if using, and press on the reverse under a damp cloth to remove creases. Cut into a tag shape, leaving a margin of 2cm of unworked fabric all around the stitched design.

Cut a piece of backing fabric exactly the same shape as the tag, place on the reverse and tack the two fabrics together, close to the edge. Bind the edges with satin trim, creating a loop of folded ribbon at the top, for attaching to a gift or to the strap of a bag.